(Note: There is no need to install Java to get the installer to run)

STM32 for VSCode. This is a supporting extension to setup STM32 projects generated from STM CubeMX. It automatically generates a makefile and starts the build process, it also adds debugging, build and flash configurations to the workspace. It also supports using cpp files, however for this main.c has to ben manualy renamed to main.cpp for it.
STM32CubeIDE integrates STM32 configuration and project creation functionalities from STM32CubeMX to offer all-in-one tool experience and save installation and development time. After the selection of an empty STM32 MCU or MPU, or preconfigured microcontroller or microprocessor from the selection of a board or the selection of an example, the.
Gregory; STM32的内部ID是一个12字节长度，我们一般都是用库函数读取到这个的内部ID，这96的数据是独一无二的器件码，d但是不能直接作为MAC地址使用，因为MAC地址一般是6个字节，我们直接截取一段ID地址，因为这个ID地址的某一段可能是重复的，所以要通过算法把把这96位数据处理生成6个字节数据.

If you are still having issues then it could just be that you have bricked your device so you will need to try a firmware recovery by shorting the boot pins while flashing, or using the STM32 Flash Loader tool to recover the firmware (search this site for a guide on how to do that if you are stuck). STM32CubeIDE integrates STM32 configuration and project creation functionalities from STM32CubeMX to offer all-in-one tool experience and save installation and development time. After the selection of an empty STM32 MCU or MPU, or preconfigured microcontroller or microprocessor from the selection of a board or the selection of an example, the.

For those that want to set up the STM33duino using the STM32 Cores on a Mac running Mojave (10.14) here is what worked for me.
Follow the excellent instructions at: https://github.com/stm32duino/wiki/wiki/Getting-Started until the 'Extra Step' portion:
(https://github.com/stm32duino/wiki/wiki ... extra-step) to install the STM32CubeProgrammer)
* Download the STM32Programmer at https://www.st.com/en/development-tools ... eprog.html
* Unzip it
* Right click on SetupSTM32CubeProgrammer-2.4.0.app (app version may be different)
* Select Show Package Contents
* Double click on MacOS
* Double click on “SetupSTM32CubeProgrammer-2_4_0_macos” to execute it
* Follow the instructions on the window that opens
The STM32CubeProgrammer is now installed.
Time to Test:
Connect your STM32 to your USB to Serial:
USB to TTL - STM32

Stm32 Virtual.com Port Driver For Mac

Ground - Ground
5 volts - 5V (make sure USB to TTL is set to 5v, or if 3.3 volt, then connect it to the 3.3 pin)
Arduino

TX - A10
RX - A9
Move jumper BOOT0 to 1, press reset, load Blink in the Arduino IDE examples.
Under Tools set the following options:
* Board > Generic STM32F1 Series (or what ever you have) Stm32

* Board Part Number > BluePill F10C8
* U(S)ART support: Enabled (generic Serial)

Stm32 For Arduino

* USB Support (if available): None

* Optimize: Smallest (-Os default)
* C Runtime Library: Newlib Nano(default)
* Upload method: STM32CubeProgrammer (Serial)

Stm32 For Motor Control

* Port: (select your USB to TTL serial port)
With everything connected, click upload and you should see a flashing LED.

Stm32 For Multisim

NOTE: to load the next program, you must press reset on the STM32 or it will error out.
*** I am new to the STM32 family so if there is anything is incorrect or misleading, please let me know ***

Stm32 For Mac